Pages

Sunday, December 1, 2013

Solid Wood Flooring Vs Laminate Flooring -- What to expect

 
Solid Wood Flooring from Colling-Wood Flooring



As a life long carpenter with nearly 30 years of experience, I can assure you that the vast majority of people that buy flooring, or decide what flooring to use, lack the basic understanding of what they are deciding to buy. They just don't know the difference between laminate and wood flooring.

The trend in new homes and renovations is to use low cost engineered, (pre-finished) flooring. They call it hardwood, because it contains a very thin layer of hardwood on the surface of a plywood/Masonite/adhesive core. They vary greatly in how they are made, the quality of finish and components and for our purpose we will refer to them as Laminates. Engineered flooring is just another name for the same thing.

We strip out old style flooring from time to time, but normally the flooring has been in place for a half a century or more, and refinished numerous times. The two floors seen here are brand new wide plank floors. Laminate flooring producers strive to make their floors look like this.

Wide Plank Butternut Flooring

What to Expect?

Cost 

Laminate flooring installed will vary between about $5 and $20 per square foot installed.  Solid wood, finished in place flooring will range starting at about $7 and range up to the $30 per square foot, finished and installed. The higher end number will feature a faux finish that is labor intensive, with clad staircases and transitions to tile included. It could take 2 weeks to do a floor like that in your average house.

Durability

Laminates in high traffic areas could look quite worn within 3-5 years. Dogs and high heels can be tough on them and you need to remember that refinishing these lacquer coated faux panels is not possible. There simply isn't enough wood there to work with.

Solid wood flooring depending on the species can last centuries. It gains character as it ages. Pine will show more wear--hard wood like ash or hickory will show less wear. So, your decision for flooring can last a few years...or a lifetime, with a similar cost.

Thickness

  Our solid wood flooring is a full 7/8" thick when you get it.

  Laminate flooring will vary between 1/4" and 3/8" generally.

Consider levels when deciding on flooring. When you change the height of a floor, this will affect the stair risers, (height of the top and bottom step--as well, finishes may not match well. Laminates are notorious for not having parts readily available or enormously expensive and time consuming to source. Many engineered flooring does not get fastened to the floor--they lay on a mat and are glued to each other. This system does not work particularly well on stairs which means jury rigging your tread cladding.

Sound Transfer 

Depending on the species, solid wood will help deaden sound transfer from the upper floors to the lower. Laminate is light weight and will not deaden sound much. We recommend gluing our floors in place, which increases the mass to include the sub floor in one thick mass. This will help keep sound transfer down and actually add strength to the floor. 


Stair Treads, Nosings and Transitions

We can fabricate stair treads, nosings and transitions if you need them--or sell your contractor the extra raw materials to do it from the same species.Since the finish goes on after installation, color matching is not an issue.

Uneven sub floors

Before installing laminate flooring you will have to achieve an even--smooth sub floor, otherwise the flooring will move and cause premature failure. When it comes to renovation work, this often means sanding the entire floor area with a large drum sander, belt sanders or palm sanders and the amount of work can be cumbersome and affect the overall budget.

Working with our solid wood flooring, the odd inconsistency in level of flooring, up to about 3/8" is fine-- just glue the flooring in place and you won't have any issues.  When you sand the flooring after installation, the inconsistencies will not be noticeable.

Choice of finish, colour and style

Laminates change their look and style with the weather--so what you buy today, may not be available 5 years from now. Buy enough for repairs and patches, and realize that if you have your new staircase finished to match your stylish new flooring, you may not be able to buy a match for the flooring later.

Old school wide plank solid wood flooring gets finished in place after sanding in place. There are tens of thousands of specialists that do the finishing for you in North America--just google it.  You choose the colour, texture, finish type and whether they accentuate flaws or knots or keep them to a minimum. The flooring specialist can supply you with finish samples prior to applying the finish.




Wednesday, August 28, 2013

How To Lay Wide Plank Flooring


 
 This is flooring like that in a homes 100 years ago--which has the disadvantage of taking a little longer to put down and finish, however, you will be able to refinish it a few times and enjoy the floor for up to 100 years.

You need to look closely at the floor that is there now because normally it will have to be removed before putting down the new. Whether it will stay together when you nail the new floor in is only one of the factors to consider. Will the nails penetrate deep enough into the sub-floor to hold tight? Will the floor work it's way loose over years to come and will the stair risers all be the same after the installation. I have only actually put a floor over an existing floor once, and that was a white cedar floor that was face nailed, tight and more like a sub-floor than regular flooring. As a rule, the existing floor gets stripped out.

Once the floor is removed, you have to look for uneven patches. Often buildings are added on to, porches become part of the room, walls between additions get removed and you may have to use a sander to even things up before you put the new flooring down.


You will choose a long run that is perpendicular to the sub floor direction and start by chalking a line. The first row of flooring needs to be put down perfectly straight. Any natural curve (crown) needs to be pulled straight. The tongue must be laid in the direction of the floor getting put down--so the tongue goes towards the outer wall.


This first row can be nailed in place or put down with countersunk screws, you will be pulling the other boards against it, so it needs to be secure.


RULE #1 for using Colling-Wood Flooring, "Always glue the flooring down".

Construction adhesive will keep the flooring in place in the coming decades. It also helps keep wide plank flat. Here we applied an exterior stain, (one that dries solid), because the basement is an open crawlspace which is damp from time to time. It will prevent the floor from cupping.



 RULE #2 for using Colling-Wood Flooring, "Trim 6-8" off the ends of each board".


The ends of the boards will be slightly smaller and there may be planer snipe (it may be a little thinner), so, trim some off the ends and you will have a nice tight floor. 
 
You will notice when you receive your flooring that these boards are up to 16' long and up to 11" wide. Most producers only make flooring up to 5" wide, and they trim the ends for you. You are buying direct from the mill--we cut it, we dry it, we plane and mill it to the profile. When you tell us the square footage we add some extra for removing the ends. I have never run short when Merv's folks calculate what I need. 

Special Tools--What to use?

   You will need basic carpentry tools, but the specialty tools you will need are pneumatic or manual nailer. These shoot pins or staples normally. I like the pins better, but the staples work fine. It is personal preference. 

   I use a 15 gauge nailer for the spots where you can't use the flooring nailer--and quite often countersunk screws and tapered plugs in high traffic areas like thresholds and stair nosings. 

  You will need a tool to pry the flooring. The guys above were using a chisel--however that was Beech--very hard wood. If you try that on pine it will crush. Always use a block to push pine or other soft woods. 

   You will need a flush cut saw to trim casings, stair stringers or anything else that might be obstructing the floor. Cutting around these things just isn't the right way to do it. 

 Here is an example, we placed a piece of rough flooring against the stringer here, and cut it clear of where the new nosing will be placed.

The thin kerf flush cut saw makes the cut just slightly larger than required...





And the nosing slides right in. We also use the flush cut saw to cut off tapered plugs prior to sanding. Remember... glue the plugs!


 RULE #3 for using Colling-Wood Flooring, "NEVER putty before finishing!".

You need to resist the primal urge to apply putty to every crack and gap and nail hole in the flooring before finishing--but the truth is, cabinet makers and professional craftsmen will never ever do it. Residue of the putty prevents stain from getting into the grains where putty has been applied...and you will see an irregularity in the finish. 

Stain, Verathane....then putty. Use color matched wax based putty for best results! 

If you have any questions...feel free to write us at the email on this page!

By: Lawrence Winterburn

Tuesday, June 25, 2013

Learning about flooring from old masters.

When you want to learn about flooring there is no better way than to remove a floor that lasted half a century. For a floor to stay down and last that long they must have done something right. --and this was the flooring that was only 1/2" thick that was sold in the early seventies and installed in millions of floors in North America. This kind of floor could only be refinished a couple of times before needing to be stripped out and often only lasted a decade or two.


We had opportunity to witness a job first hand near Barrie Ontario where the old hardwood was being removed after nearly 50 years of service.

The first thing we noticed was that they had installed tar paper, like many flooring installers do, however, they also had a layer of building paper beneath the tarpaper. It wasn't beneath the entire floor--just the area that remained tight and squeak free. It looked like part of the floor was done at a different time, because all they had beneath that portion was building paper. That whole section of the floor was loose and noisy under foot traffic.


The second thing we noticed was that there was lots of damage due to a leaky roof, and a patio/foundation issue that has caused moisture to enter the floor system yearly during spring thaw. It was coming in through the dining room and also at the patio door, so these are things that need to be addressed before the new floor gets installed. 

Between the two areas of floor, there was also a dramatic difference in the number of nails used. The tight section used roughly 2x the number of fasteners as the one that went loose. Whether there is much actual difference in performance or not, remains debatable--but in this case, in the days of pneumatic fasteners it is a fairly easy thing to install a few extra nails to help the floor last longer. 
 

Here is the new floor acclimating to the moisture levels in it's new home. This normally takes a couple of weeks to happen. This is random width white pine flooring from Colling-Wood Flooring. It is dried to 6% and will shrink and expand less because of that fact.

By Lawrence Winterburn

LIKE us on Facebook
e-mail Lisa or Merv - info@colling-woodflooring.co

Wednesday, June 19, 2013

How to wash and care for your hardwood floor



-->
It may seem like a silly topic, I mean, washing a floor should be simple, correct?

The way you wash your hardwood floor really depends on the type of sealant that you have used.  So, be sure to determine your type of finish, if any at all, because the finish, and not the type of wood, actually determines how you would safely wash and care for your floor. 

It is also important to note that water is wood’s worst enemy!  Why you ask? 

Hardwood floors can easily get water damaged even if they’ve been sealed. If a wood floor gets saturated with moisture, swelling and warping, unwanted stains or mold growth could result.  To avoid these problems, and to insure the beauty of your floors for years to come, address spills as quickly as possible.Take the time to buff your floor with a towel so that the floor is dry.

I’m not going to go on and on about the Do’s and Don’ts of cleaning your floor; however, I will emphasize the Do’s. 

Here they are:

Do use a non-toxic floor cleaning solution.  The best choice is a simple mixture of ¼ Cup of mild liquid dishwashing detergent added to a bucket of warm water.
*Toxic cleaners are not only bad for the environment, but also your health and the quality of air in your home.

Do use a sprinkle of baking soda on a damp sponge for rubbing off scuffmarks.
*Again, harsh cleaners and high acidic products such as vinegar and ammonia cleaners will eventually dull the finish of your floor.

Do vacuum and sweep wax based floor surfaces only.
*If floors are waxed, re-apply wax once or twice a year, and buff in-between to restore the original shine. Waxed wood shouldn’t be mopped; a wax seal is not watertight and liquid could cause unwanted damage.

There you have it, how to care for your hardwood floor 101.  For further questions, don’t hesitate to call the experts at Collingwood Flooring and they will be thrilled to share their knowledge and expertise on the subject of flooring! 

Written by: Melanie Vollick
Writing for several years with experience in newspaper, newsletter, website, magazine, technical and business writing, Melanie is an accomplished columnist, editor and proof reader.  Her aptitude for approaching many styles and genres of writing allow her to present incomparable written documents in a timely manner, while developing a strong presence for her clients.  

LIKE us on Facebook
e-mail Lisa or Merv - info@colling-woodflooring.com

Friday, April 26, 2013

Is the Butternut Tree a species at Risk?


Endangered Provincially and Nationally, the Butternut tree or also known as White Walnut is suffering from an incurable disease that is quickly wiping out the species.

The main threat to the Butternut is a serious fungal disease called Butternut Canker, which was first found in Ontario trees in 1991. It has been traced in North America for approximately 50 years.  The disease is thought to have arrived in infected plants imported from overseas. A similar blight was responsible for wiping out both the American Chestnut and the American Elm.

Once the fungus takes over, the tree dies within a few years of infection.  Colling-wood Flooring has recently been able to get permission to cut down some of the dying Butternut from the Ontario Ministry of Natural Resources. 

The butternut species is relatively short lived, rarely living longer than 75 to 100 years of age and the disease is found in an astonishing 90% of the Butternut in Ontario alone.  Unfortunately, the trees have disappeared from many parts of the United States and Canada.

According to the Ministry of Natural Resources there is no cure for the Butternut Canker disease so order now, as it may be your last chance!  Colling-Wood Flooring has approximately 10,000 square feet.

Merv Gardner started Colling-Wood Flooring in 1990. He is a special man with a heart for wood and for 40 years, Merv has been honing his woodworking skills and now has his star pupil and daughter Lisa working at his side.

Written by: Melanie Vollick
 Writing for several years with experience in newspaper, newsletter, website, magazine, technical and business writing, Melanie is an accomplished columnist, editor and proof reader.  Her aptitude for approaching many styles and genres of writing allow her to present incomparable written documents in a timely manner, while developing a strong presence for her clients.

For more information or to order your one of a kind, butternut flooring, please feel free to give Merv or his daughter Lisa a call – (705) 445 1147.  
Feel free to also LIKE their Facebook Business Page https://www.facebook.com/CollingWoodFlooring.
Click here to check out their website - Colling-wood Flooring

Price: Butternut starting at $6.50/ sq. ft.

BUTTERNUT FLOORING
6" 8" 10" AND 12" WIDTHS
13/16 THICK TONGE AND GROOVED UFINISHED
KILN DRYED TO 6% - NO SHRINKING